How to glue non-woven wallpaper in the corners without folds and curved lines. How to glue wallpaper in the corners of the kitchen: glue the corners with wallpaper correctly, decorate the outer corner, non-woven trellis, instructions, video

Non-woven wallpaper is a wallpaper, which is used in the manufacture of non-woven cellulose material non-woven. Unlike paper counterparts, such wallpapers are perfectly washable, allow you to hide even fairly noticeable wall irregularities and retain an attractive appearance for a long time. Yes, and the process of gluing non-woven wallpaper is quite simple - the material is quite obedient, does not "pull" either horizontally or vertically, and practically does not give "bubbles". And even in such "problem" places. both external and internal corners, non-woven wallpaper is glued without any problems - for this, when gluing, it is enough to follow a few simple rules.

How to glue non-woven wallpaper on internal corners

The first thing to say about gluing non-woven wallpaper in the corners (both external and internal) is you can not try to paste over the corner with a solid canvas of wallpaper. In other words, do not try to cover both walls adjacent to the corner with one canvas. Otherwise, it is quite likely that the wallpaper will “lead” in the corner, and the resulting folds will be almost impossible to smooth out without trimming, which will certainly spoil the appearance of the wallpaper. But even if this does not happen, the curvature of the corner (and unfortunately most of the corners in our apartments are crooked) will affect the location of the canvas, and since the non-woven wallpaper is glued “butt”, all the following canvases will also have to be glued out of level.

The correct technology for gluing non-woven wallpaper on internal corners is as follows:

• We measure the distance from the edge of the last glued canvas to the corner and add 5 centimeters to it. A panel of just this width will need to be prepared for sticking into the corner.

We measure the distance from the edge of the last glued canvas to the corner

Since the angle can be curved, it is better to measure the distance at three points: at the bottom, in the middle and at the top of the wall. For calculations, of course, you need to take the largest of the resulting values.

• When the panel of the required width is ready, carefully coat the wall and corner with glue for non-woven wallpaper. Please note that when gluing non-woven wallpaper, glue is applied only to the walls.
• After the canvas is pasted, very carefully, using a rubber roller or a dry cloth, smooth the wallpaper in the corner and on the next wall.

Using a rubber roller or a dry cloth, smooth the wallpaper in the corner and on the next wall.

If the wallpaper “wrinkles” in some places, you can make several horizontal cuts at a distance of 5-10 centimeters from each other.

Please note that this canvas must be glued "overlap" on the previous canvas.

• When both canvases are glued, it remains with the help of a wallpaper cutter and a metal ruler of a paint spatula to make a “trimming of the seam”. You can learn more about the technology of "corner trimming" by watching the following video.

Video about corner trimming wallpaper

It is very important to cut through both wallpapers “in one go”, otherwise discrepancies in the cut line may appear.

In order for the cut to turn out even and the wallpaper under the knife “did not stretch”? you need to periodically break off the blunt tip of the wallpaper knife according to the marks specially applied to the blade.

• After trimming, it remains to remove excess wallpaper. The top layer can be removed without problems, and the bottom layer can be removed by slightly unscrewing a small part of the top panel.

If you did everything correctly, then the panels form an almost imperceptible joint between themselves, which will remain carefully smoothed with a rubber roller.

Glue on outside corners

Outer or outer corners are not found in all rooms, but, nevertheless, they can be found quite often. The technology of sticking non-woven wallpaper on such corners practically does not differ from the method of pasting internal corners.

The technology of pasting the outer corner is almost the same as the method of pasting the inner corners.

First of all, we measure the distance to the corner from the extreme panel and prepare a new sheet of wallpaper in such a way that after the sticker they “turn” around the corner by no more than 5 centimeters. From the turning point closest to the corner, we measure the distance for gluing the next canvas (roll width minus 1 centimeter). We glue the canvas "overlap" on the resulting inversion, after which we trim the seam with a wallpaper knife and remove unnecessary parts of the wallpaper.

If the outer corner is fairly even (this can be determined using a plumb line), you can try to paste over it with “one canvas”. But keep in mind that the level difference in this case should not exceed 0.2-0.4 centimeters. Otherwise, it is better to glue non-woven wallpaper according to the technology described above.

As you can see, there is nothing complicated in pasting corners with non-woven wallpaper, so after a little practice you will be able to do this job perfectly. Good luck with your repair!

by the most in a simple way updating the interior of the apartment is pasting the walls with wallpaper. However, while doing the work, many face some difficulties. The greatest difficulty is gluing wallpaper in the corners. In these places, when carrying out repairs, many make mistakes that spoil general form updated finish. It is enough to familiarize yourself with the algorithm, which suggests the correctness of such actions, and such problems will no longer arise during subsequent repair work.

Wallpapering in corner areas

The main difficulties that apartment owners face when pasting walls with finishing materials are uneven external and internal corners, often having uneven geometry. All this not only complicates the process of gluing decorative material, but also significantly increases the repair time, which is hardly included in the plans of any person.

Ultimately, the owners of the premises are forced to additionally process the surface of the walls. However, even subsequent use quality materials is no guarantee that the corners will be perfectly even. This gives the impression that the work is done unprofessionally and spoils the overall look of the room.

Few people know how to properly glue wallpaper in the corners of a room. In order to properly perform this process, it is necessary to follow a certain sequence of actions. Before doing this, remember the following:

As the work approaches the next wall joint, the strip of wallpaper is trimmed so that it is only a few inches pasted onto the adjacent wall. Then the wall treated with adhesive. After the strip is fixed on the wall, it needs to be ironed rubber spatula or press with a roller. It is important that there are no folds at the junction of two walls, even if an uneven bevel of the edge of the strip is obtained on the adjacent wall. If the material is very dense, then shallow cuts can be made from the inside of the finishing paper material. In this case, the canvas will be better adjacent to the interface of the walls.

Then, on the wall, where there is a smaller part of the wallpaper strip, a straight line is drawn from floor to ceiling using a level or plumb line. In this case, you should retreat from the corner by the width of the roll. Next, the glue is applied to the wall, and a strip cut is applied to the existing line. At the same time, its edge will overlap jagged edge the previous piece of wallpaper.

When both bands are fixed, it is necessary to determine the place of the smallest overlap. It should be divided in half and draw a straight line from the middle along the entire height of the corner, then cut it with a sharp knife or blade.

The upper piece of material must be carefully removed, folded over and the cut off part of the lower strip removed. Then both edges of the wallpaper are smeared again glue, close and gently smooth out with a roller. The result should be a perfectly even angle, and there will be no sags or gaps at the junction.

Carrying out wallpapering in the corners, it is necessary to wait some time after fixing them on the wall. Otherwise, the material wet from the adhesive composition cannot be cut evenly. As you can see, there is nothing complicated in this process if you follow the algorithm

.

Such corners are much less common indoors. Wallpapering them works in a similar way:

It must be remembered: even in the case of perfectly even corners, one should not strive to wrap the whole canvas. This is most often leads to wrinkles and irregularities, as well as a high probability that the material will swell and bristle ugly. As a result, it will be necessary to repair work again, which requires financial costs. The whole canvas is wrapped only when wallpapering on window or door slopes.

Cutting off part of the canvas will not lead to a large consumption of wallpaper, so gluing wallpaper on the corners will not require an increase in spending. In general, the work is not difficult, but there are small nuances. If you take them into account, everything will be done correctly in accordance with your own requirements. If there is no self-confidence, it is better to entrust the work to professionals.

In the manufacture of non-woven wallpaper, non-woven cellulose is used.

Advantages of the material - easy wet maintenance, concealment of irregularities in wall panels, attractiveness appearance a long time and a fairly simple pasting process.

Due to the obedience and non-pulling of the material, even such a stage as gluing non-woven wallpaper in the corners passes without the formation of “bubbles”.

This finish is not made of paper, but of interlining. This is a non-woven type gasket material based on cellulose fibers.

These cellulose fibers can be sized or not, modified or not.

There is a purely non-woven version using up to 70% long cellulose fibers and special additives.

Pluses - air and vapor permeability of the material, smoothing of wall irregularities and reinforcement of microcracks.

Pasting is carried out without the presence of bubbles, without shrinkage of the longitudinal and transverse.

There is an option with non-woven base instead of paper. They are classified as vinyl. The surface of such material can be smooth, foamed and embossed, for painting.

Minus - the airtightness of the material. Pros - the effect of leveling and reinforcement, the possibility of wet cleaning using detergents.

If you want to update the finish upper layer material is removed from the wall, and the non-woven base remains, acting as a reinforced base for new wallpaper.

Pasting features

This material is considered quite "obedient" and, following the step-by-step instructions, there will be no problems when gluing large strips of canvas and how to glue non-woven wallpaper in the corners.

For this type of finish, special glue is sold, and the walls are pre-primed for better laying of the material on the surface of the wall panels.

Technological difference this process is the absence of the need to smear the canvases themselves. The adhesive composition is processed only wall ceilings.

The cutting of the material is carried out taking into account the pattern and with an upper and lower allowance of 1.5-2 cm to the length of the web.

Pasting is done end-to-end according to the markup. The glued canvases are leveled with a roller to release air and excess glue from under the canvases to the seam.

The glue is removed with a damp sponge to preserve the aesthetic appearance of the finish.

Tools:

• For even pasting, a plumb line or building level;
• Long tape measure from 3 m;
• For smoothing a roller with a long pile material;
• Brush and plastic spatula;
• Sharp knife, pencil and grid;
• Containers for adhesive and water;
• Narrow spatula made of metal;
• Sponge.

Work progress

Technically, gluing wall panels with non-woven fabrics is carried out in 3 stages: preparatory work and wall markings cutting wallpaper; the direct process of their gluing.

Overlapping of wallpaper cloths is carried out starting from wall panel perpendicular to the window and moving deeper into the room.

Thus, the light will help smooth out the seams. But the non-woven version is glued only end-to-end.

Additional related video:

The quality of the edge edges of the wallpaper strips allows pasting without visualization of the joints. For the success of the pasting process, it is better to start from the corner of the room.

markup

Having chosen the angle of the start of work, 1 m is measured from it, for meter-long wallpaper, on adjacent walls. The standard width is 0.53m or 1.06m. 0.06m will be used for the corner overlap.

For pasting wide wallpaper must be absolutely even.

Having made a measurement at 1 m from all corners of the room with a plumb line or level, a vertical line is drawn on the meter marking.

You can use strokes in increments of 40 cm.

Cutting cloths

The volume of all canvases is prepared immediately, taking into account the fit according to the pattern. Monochromatic canvases are easier to cut and so much remains finishing material.

The strips are cut in such a way that when they are combined, there is no need to glue individual strips on top or bottom.

For the cutting process, polyethylene is spread on the floor, on top of which a wallpaper roll is rolled face down.

The cutting of the 1st strip is made along the length of the walls + 10 cm for allowances. A notch is made with a knife, along which the canvas is bent: the edge of the bent strip must coincide with the edge of the main canvas.

An angle of 90 ° is formed and the wallpaper is cut along the fold.

The rolling of the next sheet starts from the same place, observing the cutting direction.

It is necessary to check for pattern compatibility, and mark the top of each strip, which are rolled face inwards from bottom to top.

Pasting inside corners

You can not paste over the corner with a solid panel. Steps:

Measurement of the distance from the edge of the last strip to the corner with an allowance of 5 cm.

With a curved angle, the measurement is made at 3 points: bottom, middle and top of the wall panel. For calculations, the largest value is taken.

The wall surface and the corner are carefully smeared with glue. After sticking the strip, it is carefully smoothed out in the corner opening and on the next wall.

When wrinkling the wallpaper, horizontal cuts are made in increments of 5-10 cm.

The curvature of the corner opening can affect the variance in the width of the wallpaper overlaps. Therefore, in the narrowest place, markings are made with an indent of 1 cm from the edge of the strip towards the corner.

From this point, the distance in the width of the material is measured and a vertical is drawn with a plumb line. From this place the next lane will go. Gluing is carried out with an overlap.

External corners

The distance to the corner protrusion from the last strip is measured and the next one is prepared so that it wraps around the corner up to 5 cm.

From the nearest point, the distance for the next strip is measured in the width of the material minus 1 cm.

Pasting is carried out with an overlap on the inversion. Next, the seam is trimmed and the excess removed.

Another video

Evgeny Sedov

When hands grow from the right place, life is more fun :)

Mar 2 2016

Content

Often wallpaper materials are the most familiar wall decoration. Their popularity has increased due to affordable price and ease of pasting, but not in all places. Anyone can handle smooth surfaces, but in the question of how to properly glue wallpaper in the corners, not everyone can prove themselves as a professional. In order not to slow down the repair process and make it better, you will have to resort to some construction tricks.

Features of wallpapering in the corners of the room

Pasting a straight wall surface is not difficult, but as soon as you reach the turn, the hassle begins. How to glue wallpaper in the corners? Already experienced people in this matter recommend that beginners observe several conditions:

1. Do not use the whole canvas on the turn. No matter how smooth it may seem, folds and distortions still turn out, because some modern wallpaper materials shrink after drying.
2. Do not start pasting from the very junction of the walls - it is not as smooth as at first glance. It turns out that two panels are spoiled at once. Instead, you need to take a level and draw a vertical line.

There are 2 ways to glue wallpaper in the corner:

1. Lay the sheets overlapping each other and make a cut in the center of the overlap. Remove cut pieces.
2. Glue one panel, leading the edge 1.5-2 cm per turn, then butt him - the prepared second piece of material.

Wall preparation

Before gluing, you need to make preparatory work:

1. Inspect the joints of the walls themselves for irregularities. They need to be leveled with putty, which will dry for a couple of hours. After that, smooth the surface with sandpaper to achieve perfect smoothness.
2. Using a level with chalk, draw a straight vertical line, stepping back from the junction of the walls by 4-5 cm. There will be an edge of the canvas.

Step-by-step technique for doing work

To start pasting, you need to prepare necessary materials- all of them should be at your fingertips. Wallpaper sticker in the corners requires the following:

• wallpaper cloths of the desired length with a margin of a couple of cm;
• diluted in warm water adhesive suitable for the characteristics of your material;
• roller and brush for applying glue;
• dry cloth to wipe off excess adhesive;
• brush for leveling panels;
• ruler;
• construction knife;
• a stool to reach the top of the canvases.

How to glue inside corners

Here are the stages of work, how to glue paper wallpaper in the corners:

1. Applying glue. Thoroughly coat the joint surface of the walls with the prepared composition from top to bottom, because there the material peels off easier and more often. Use where you get a roller, and where you need a brush.
2. First part. On the side where the material is already pasted, glue the next part so that it falls around the turn by about 4-5 cm, as shown in the photo. Press the edge with a sponge. Press harder on the turning point to fix it more carefully.
3. The second part. Proceed to another wall. Knowing the width of your material, measure it on the wall so that one edge of the panel extends 2-4 cm onto the previously glued one. Draw a line, checking it for verticality. After applying glue to the wall, glue the second canvas. Press the edges with a sponge.
4. Trimming excess. Arm yourself with a ruler and a construction knife. Make a vertical cut in the center of the overlap using a ruler. Carefully tear off the top panel from the wall and remove the lower trimmed part.
5. Final bonding. Thoroughly coat the part that was turned away with adhesive and re-glue it to the wall, smoothing the edge and removing excess glue. The perfect seam is ready!

How to glue outside corners

The protruding parts are more visible in the room, so they must be done especially carefully. There are two options for how to paste the wallpaper yourself:

1. The protrusion is perfectly flat. Then just wrap the canvas around the corner joint by 3-4 cm and glue it. Do not cut it, and glue the next one using the usual technology for a straight surface.
2. The walls are uneven. You'll have to use another method.

The second method will not differ from the technology for internal corner joints. Here's how to properly glue wallpaper in protruding corners:

1. Glue the first strip with an overlap at the corner joint of about 4-5 cm.
2. Measure the width of the panel from the ledge and step back another 5 mm so that when gluing one part runs a little over the other.
3. Make a cut along the ruler in the middle of the overlap.
4. The upper part will fall off by itself, and remove the lower part by pushing the top sheet and gluing it in place.

Such methods are assumed for those materials that are glued butt-to-butt and do not give shrinkage deformations. So the seam will not disperse and there will be no gaps in the wall. For paper materials these methods will not work - an overlay of 0.5 cm is required, so the first method is used when the overlap is not cut, but simply checked for verticality with a plumb line. If deviations are found, draw a line and cut off the unnecessary. For a more aesthetic design, a wallpaper corner is often used.

Non-woven wallpaper - a great option for finishing building material combining practicality, convenience and beauty. In the process of sticking such wallpaper Special attention you should pay attention to how to glue non-woven wallpaper in the corners evenly. Pasting with such material has a number of features that must be considered when working. For example, in order to glue a non-woven decoration, a special adhesive based on non-woven fabric is used. Also, non-woven wallpaper does not require the application of glue to the canvas itself, in addition, this type of finishing material does not shrink during operation. Basically, their gluing is carried out end-to-end (with the exception of external ones).

The scheme of gluing wallpaper in the corners.

Tools and materials

So, in order to glue the non-woven decoration, the following tools and materials are needed:

• non-woven wallpaper;
• special glue;
• construction roulette;
• building level;
• simple pencil;
• metal spatula 350 mm;
• metal spatula 150 mm;
• stitching roller;
• containers for the preparation of glue, solutions;
• cutting knife;
• roller or brush for applying glue;
• plastic spatula.

How to glue inner corners with non-woven wallpaper?

Scheme of the sequence of gluing non-woven wallpaper.

It should be noted that there is one optimal and correct way that tells you how to glue corners with non-woven wallpaper. Before pasting, the walls of the inner corner must be properly prepared: the old coating is removed, plastering work is carried out (if necessary), the walls are leveled, a primer is applied, etc. The adhesive must be prepared according to the instructions immediately before use.

In addition, the marking of the wall is necessarily done: with the help of a building level, a straight vertical line is marked from the edge of the inner joint at a distance equal to the width minus 1-1.5 cm. distance from the joint to the edge with the addition of 1-1.5 cm. It should be noted that best option- this is a method in which each side of the inner corner is pasted over with a separate panel. To do this, apply glue with a roller on the marked part of the wall. The area of ​​application should correspond to the area of ​​the canvas to be glued.

You should also apply an additional layer of glue with a brush along the very edge, along the upper border of the wall and below, directly at the baseboard.

The prepared canvas (with an allowance of 1-2 cm in length) is applied, starting from the top, to the wall treated with glue, and ironed with a construction spatula in the direction from top to bottom and from the center to the edges. Thus, the excess is removed. In this case, the left or right edge of the canvas (depending on which side is pasted over) coincides with the marking line applied earlier. The excess is removed in the following way: starting from the top, close to the pasted wall, a metal spatula 350 mm long (for even walls) or 150 mm long (in the case of uneven walls), then the excess is removed with a cutting knife, while the knife blade moves along the metal plane of the spatula.

It should be noted that the blade of the cutting knife must be sharp in order to avoid defects when removing residues. The second part of the internal joint is pasted in the same way. As a result, a junction of panels is obtained along the edge. Of course, if not a corner, but another landmark is chosen as the starting point for pasting, then it is possible to paste over with a part of the canvas of the appropriate width with a deduction of 1-1.5 cm.

Trimming excess is carried out with a knife and spatula.

Joints on a horizontal surface after gluing are processed with a stitching roller.

How to glue the outer corners with non-woven wallpaper?

For pasting the outer corners, all of the above preparatory operations are carried out: leveling the walls, preparing glue, etc. It is preferable that there is exactly a whole canvas on the outer corner. This gluing option is suitable for even external joints, which must be glued taking into account the selection of the pattern.

If the whole canvas cannot be glued during the pasting of the room, then the outer corner is pasted over with a wallpaper panel so that the overlap is 1.5-2 cm. The other side is pasted over with a whole canvas, while the edge of the panel is glued to the edge. This option is most preferable if the material is intended for painting, which will hide pasting defects. However, this option is not suitable for wallpapers that need to be glued taking into account the selection of the pattern.