Dir 615 firmware ftp. Setting up DD-WRT for Domolink and IPTV

Initially, I was set to buy a router, since I have been buying different pieces of iron from this company for a very long time and have never been disappointed. But after looking at the Asus, they also push alternative firmware, and somehow it broke me off paying 3-4 thousand wooden ones for the router. In general, I decided to choose one of the ovs, although my attitude towards them has not been very good for a long time, but there was work and a bunch of working computers hung on it, and in principle I have nothing to load it with, except for a smartphone and client laptops. Before buying this router, I already decided in principle that I would definitely not use my native firmware, but put an alternative one. But still I decided to try to use my native one for a couple of days, setting up the Internet took no more than a couple of minutes, including waffles (wi-fi). Everything worked except for the waffle breaks on the smart when not used for a long time, later I tried to play over the network and it was already clear that it was time to flash the router, because the connection with the servers was interrupted stably, after 5-10 minutes. Although when connected via cable, everything became normal.

The firmware procedure is as simple as possible.
• Download the firmware from here, choose your revision - dd-wrt
• Next, go to the admin panel of the native firmware (http://192.168.0.1/) in Firmware Update, select the previously downloaded firmware file and click update.
• After installing and rebooting the router, go to http://192.168.1.1/, and not as it was before http://192.168.0.1/

Everything is on the firmware, but one BUT may occur, which can slightly shake the nervous system. For example, it didn’t immediately get up for me, and the firmware recovery mode completely refused to start in the way described on various forums. It helped me in this case, as usual in such situations, the "poke method":

• 1. Turn off the router by pulling out all the cables (both power and LAN) from it.
• 2. Register a static IP address 192.168.0.2, mask 255.255.255.0, gateway 192.168.0.1, DNS 192.168.0.1 in the network connection settings on the computer
• 3. Connect the computer and the router through the WAN port on the router.
• 4. Press and hold Reset on the router for 5 seconds.
• 5. Turn on the router (plug in the power).
• 6. Wait 5-10 seconds (in the case we need, the WAN indicator should appear, and the power indicator should blink orange).
• 7. Release Reset.
• 8. Go through the browser to the address 192.168.0.1
• 9. On the page that opens, click Browse and select the original firmware file for the router.
• 10. Select the original firmware file for the revision of the router and click send.

In my case, I had to suffer precisely because of 4 and 6 points.

All the identified problems that I noticed in a couple of days of using the router on native firmware were fixed with an alternative DD-WRT firmware, and a more functional and adequate admin panel appeared.

It also happens that someone's indicators stop working after an alternative firmware, but this is also solved by installing drivers, which I basically ... It still hangs sideways for me, although my indicators work.

First, a few notes on the models that came across:
- If you have D-Link Dir615 HW version E*, then first you need NECESSARILY reflash the router to firmware version 5.11RUB03beta02, which can be downloaded from the D-Link ftp server
- If you have D-Link Dir615 C2- it is first necessary NECESSARILY reflash the router to firmware version 3.03 RU B09, which can be downloaded from the D-Link ftp server
Internet access speeds are constantly increasing, equipment is being improved, its performance is growing, but for previously released devices, the access speed can be very modest.
Informsvyaz tested the performance of D-Link Dir615 routers in different modes, the table shows the maximum speed values ​​\u200b\u200b(indicative data):

1. Connect the Ethernet cable that comes with your apartment to the port Internet your router.

2. Check the LAN connection settings (In Windows XP- Start, Control Panel,(classic look) Network connections. In Windows Vista, network settings are accessed via Start, Control Panel(classic look), Network and Sharing Center, Manage Network Connections, and in Windows 7 through Start, Control Panel, Network and Internet, Network and Sharing Center, Change adapter settings). Next, in the window that opens, right-click on the local connection icon and select the item in the context menu Properties.
Left-click once on the item Internet protocol TCP/IP and click on the button Properties.
The settings should be similar to those shown in the figure:

3. Connect the computer's network card and one of the ports of the router, for example, port number 1, with an Ethernet cable, as shown in the figure.

4. Open a browser window and in the address bar type http://192.168.0.1 and press Enter. In the authorization window that appears, in the field user name enter admin, field Password leave blank, and in the field Enter the correct Password.... enter the characters generated by the security system as shown in the figure.

5. After pressing the button log in the settings page will open. In the tab Setup this page, select a section Internet(left) and press the button Manual Internet Connection Setup:.

.

6. In the page that opens, make the settings as shown in the figure. IP address, gateway address and DNS servers indicated on the registration card.

Attention!! For the correct operation of the IPTV + Internet connection, the router must be configured using the PPTP protocol.

1) In the field My Internet Connection is choose Russia L2TP (Dual access).
2) Activate the item below static IP.
3) In the field L2TP IP address enter your local IP address.
4) In the field L2TP Subnet Mask enter your subnet mask.
5) In the field L2TP Gateway IP Address enter the address of your network access gateway.
6) In the field Server IP/Name enter the L2TP server address, i.e. L2TP.freedom
7) In the field username enter your account name (login).
8) In the field Password enter your network access password.
9) In the field Verify Password re-enter the password for accessing the network.
10) Activate the item Always opposite the parameter Reconnect mode.
11) In the field Primary DNS address 195.98.64.65
12) In the field Secondary DNS Address enter the DNS server address, that is 195.98.64.66
13) Parameter value MTU leave equal 1400 .

Save Settings located at the top.

7. To access local network resources Freedom you need to set up static routing.
To do this, go to the tab ADVANCED and activate section Routing(left).
Make settings according to the following figure:

1) You need to check the boxes next to the first lines.
2) In the first rows of the column Interface must be set to WAN(Physical Port).
3) Filling columns Destination IP and netmask see picture.
4) In the first rows of fields Gateway you must enter the address of your network access gateway.

After filling in all the fields, press the button Save settings located at the top.

8. By default, the speed mode is set on the WAN port. auto, but if there is a decrease in the speed of working on the Internet or in a local network compared to the speed of working without a router, for optimal speed matching, you can try in the tab ADVANCED select section Advanced Network(left), set parameter value WAN PORT SPEED equal 10Mbps and press the button Save settings

In chapter Advanced Network the ability to watch TV shows (IPTV) when using a router is also configured by checking the box Enable multicast streams(If the menu is Russian, then Advanced settings, Advanced network settings, Enable multicast streams.)

9. If you have several computers and you want all of them to have access to the network, then to do this, configure their network cards in the same way as the settings given in paragraph 2 of this manual and connect the network cards of computers with free ports of the router using Ethernet cables.

10. To set up a connection using a wireless network, go to the tab Setup and select section Wireless Setup(left).

11. In the page that opens, make the settings as shown in the figure.

1) In the field Wireless Network Name enter a name, for example dlink.
2) In the field security mode you take WPA Personal.
3) In the field WPA Mode select Auto (WPA or WPA2).
4) In the field Cipher Type select TKP and AES.
5) In the field Network Key enter the key (password) to access your wireless network.

After you have entered all the settings, click the button Save settings located at the top.

12. Set up your Wi-Fi card on your computer to access the network.

To do this, left-click once on the network card icon in the lower right corner of the screen (next to the clock).

In the window that appears, click the button To plug and type Wireless Network Access Key that you asked earlier.

Notes.
1. Routers with older firmware may become unstable or unable to access local resources. This problem is solved by updating the firmware of the router to the latest.
After the firmware, it is necessary to reset the existing setting and configure the router again.
ATTENTION!!! After updating the firmware, the warranty on the router is not lost. But still, be careful when flashing, otherwise you can disable the device!
2. When setting up, it is better to use the latest firmware versions.
3. When working through a router and there are no funds on the personal account, the statistics server may not open to activate the Internet card. Helps selection in the field Reconnect Mode: values Connect-on demand followed by saving the settings by pressing Save settings.
4. You can find the latest firmware version for D-Link routers on the manufacturer's website http://ftp.dlink.ru/pub/Router/. It must be saved on the computer. To reflash the router, you need to go to the menu TOOLS, Firmware, FIRMWARE UPGRADE, using the button Browse specify the path to the firmware file and click Upload.

The D-Link DIR-615 router is widely used among users. Detailed information about it tells the page of the router. Based on this, it will be necessary and relevant to provide complete data on how the firmware is updated for this equipment. This model has good characteristics and is suitable for organizing a wireless connection at home. We can say with confidence about him - a combination of price and quality.

When you buy a router, the firmware will already be installed on it. Depending on the release date, this may be a new or obsolete release. It doesn't matter what software is installed in the box. If you adhere to the requirements for installing the latest releases, then simply update it before setting up the router. Similarly, if the equipment is used for a long time, and the update was not performed, the firmware may become outdated. In some cases, if internet outages occur, manufacturers recommend replacing the release with the latest stable one.

In general, experienced users advise to replace the software immediately for new equipment, but for devices that work stably for a long time, leave the old version, especially if there is no need to update.

It should also be noted that when updating, the instructions should be strictly followed. If you make a series of mistakes, then there may not be a way back, as a result, the router will turn into a brick. After downloading the new firmware version, all network setup data will have to be re-entered. If you are not completely sure that you will be able to perform these operations, you should not update the software.

In new firmware versions, a number of new functions are often found, network operation is more debugged, bugs have been fixed. In addition, changes are made to the design and ergonomics of the administration panel.

In order to determine the hardware version of the router, you need to take the device itself and turn it over. On the reverse side there will be a label that contains the necessary information. An example is shown in the image.

For this case, the information that is given after the word "Ver.:" will be needed. In the given example, this K1. Other options are allowed, for example, K2.

After the version is determined and remembered, you should go to the manufacturer's server. You can do this at the link ftp.dlink.ru/pub/Router/DIR-615/Firmware/ . There you need to select the desired version, in the example - "K".

Sometimes you have to go to subfolders.

A directory contains several folders. Usually these are old - previous releases, beta - versions of releases that have not yet been debugged. You will need to find a file that has the extension . bin. Its name will look like this: 20140711_1343_DIR_615K1_2.5.4_sdk-master.bin. the name lists which version of the router it is intended for, when it was created, and which firmware version is used. It is most often located next to folders.

You will need to copy it to your personal computer. The storage location is chosen arbitrarily, desktop or software catalog is allowed.

When the saving process is completed, you can proceed to the firmware update.

How to update the firmware of a D-Link router

Before starting the procedure, you should remember a few important rules.

1. Check that the downloaded firmware version is correct for your router. You should double-check the revision on the box and compare it with the name of the software.
2. Firmware update is done via cable only. Wi-Fi operation is strictly prohibited.
3. The device cannot be turned off during flashing. You should also make sure that there is a constant connection to the network and power. Disabling them leads to irreparable results.

For the DIR-615 router, 4 different settings panel designs are allowed. Therefore, it will not work to give a universal instruction for everyone. The example will use the most common versions. Much easier when it comes to updating firmware on Tp-Link. It has completely identical panels and parameters.

First, connect your device to your computer with a network cable. A laptop is allowed. In the basic configuration there is a cable of small length. When a wireless connection was previously configured on the computer, it must be disabled. It is important that the connection is only through a cable.

After that, open a browser and enter the management section at 192.168.0.1. On the authorization page, enter a valid name and login key. They can be set by you when changing parameters or remain standard. admin and admin.

When the main page of the administration panel has loaded, look at its appearance, if it looks like the figure below, then you should go to the tab Advanced settings. There will be a button System. Opposite the inscription there are arrows to the right. You need a link Software Update.

If the design of the administration panel is in light colors, then you should select the item Set up manually. Further actions are performed similarly. Need a tab System, chapter Software Update.

In order to download a new firmware, you must select it on the computer. To do this, click the button Review…. In the specified directory, mark the file and click on Update. The update process will start.

We are closely following the process. While the update status is displayed, nothing can be touched. You should wait until the router reboots. On average, you should wait 4-5 minutes. After that, you can refresh the browser page. If the operation was successful, a new administration panel will appear and a suggestion to change the access data.

You can use the standard admin values ​​or come up with your own. The main thing is that they are recorded in some place.

Automatic firmware update

If the Internet is configured on the router, then the update operation can be performed much easier. The router has an automatic update function. In this case, the device will automatically find the required firmware version and download it. An error with selecting the wrong file will be excluded.

In some cases, the update function may not be available in the router settings. Or the appearance of the firmware may differ from the one shown in the example. In this case, you must first upgrade to the latest version available on the server manually.

If there is a message, then you can click on the button Update. After that, you will need to confirm the operation with the button Yes.

Then a warning message window will appear. The update process will start. Similarly with the manual method, you will need to provide a new password. It is entered twice. Once indicates, the second - is confirmed.

After the update is completed, the appearance of the administration panel may differ. When flashing the D-link DIR-615/A model to release 2.5.20, the settings look like this.

In the new version, the update is available in the System tab, which is located on the left.

Users can start the process manually, or check for new versions automatically.

In this case, it is not entirely clear why changes are made to the design of the administration panel with each firmware update. There is no significant improvement in ergonomics, but the inconvenience is serious. It is much more profitable if one design option is created and bugs are fixed or functions are being debugged. Depending on the firmware version, the appearance and arrangement of elements may differ. Now you know how to update the firmware of the D-Link DIR-615 router.

The D-Link DIR-615 router needs firmware to eliminate the “bugs” of operation: device freezing, speed reduction, overheating. The article provides a step-by-step process for updating the factory firmware.

We will tell you how to update DIR-615, where to download the program and how to restore the stock firmware.

Why do I need DIR-615 firmware?

Firmware is software that is "sewn" into the microprocessor and controls the operation of the router. The components of the firmware are combined and subsequently it is written to the device's memory.

Why update the firmware

The manufacturer installs the original firmware, but in the process of using the router, instability is detected.

In addition, if the router is not the latest model, then the installed software is outdated. Because of this, security gaps appear: access to settings, wireless network, site blocking is open.

The updated revision of the firmware is designed to eliminate vulnerabilities and improve device throughput.

How to find out the version

In order for the DIR-615 update not to damage the device, download only the firmware that matches the router model.

As a rule, the standard information about the router is on the label of the device, indicated on the box and in the manufacturer's instructions (supplied).

The DIR-615 model is found in different revisions - K1, K2, zero. How to update the DIR-615 firmware, we will show on the example of the E4 assembly, version 5.10 Ru

Firmware download

To update, you will need the firmware of the D-Link DIR-615 router from the official website of the manufacturer DLink. The last update of the program is dated 05/25/2018.

1. Go to FTP Downloads (D-Link's server hosting the hardware software). The programs are located in separate folders corresponding to the type of instrument.
2. Locate the "Router" folder.
3. From the list of firmware, select the one you need by name and open it.
4. Find the "Firmware" register.
5. In the catalog, find the revision corresponding to the router model.
6. Firmware builds that were released for DIR-615 (including test ones) are located in the beta and old folders.
7. Open beta and download the firmware. Click "Save As" and "OK".

If your router has a different revision, find a suitable one on the site.
Firmware installation process

Before flashing the D-Link DIR-615 router, disconnect the Internet cable from the WAN port. Leave only the connection to the computer.

Do not turn off the power of the router, this will damage the equipment. Do not update the firmware over Wi-Fi, only through a wired connection.

Manual update

1. Open the router's web configurator. To do this, enter the IP address 192,168,0,1 in the browser,
2. Log in to your Personal Account. Enter your username and password in the appropriate fields.
3. At the top, open the "Tools" section, in the list on the left, go to the "Firmware" tab.
4. Scroll down the page to the "Firmware Upgrade" section.
5. Click the Browse button and select the firmware file.
6. After the firmware has appeared in the field, click "Upload".
7. The router will go into reboot mode, the power indicator will turn on steadily.
8. The icon for connecting to a computer and a Wi-Fi network will gradually light up. In this case, the previous settings will be preserved.

Automatic update

On the DIR-615 router, the firmware is also updated automatically.

To do this:

1. Log in to the configurator and open the "System" section on the main screen. Here you will see the available version of the updated firmware.
2. Click the Update button.
3. A warning will appear stating that problems will arise due to incorrect software. Click Yes.

After the firmware is installed, the interface design will change.

Router Firmware Emergency Recovery Algorithm

To return the router's custom firmware, download the updated revision from the manufacturer's website. How to do this is written above.

It is important to observe the key points:

1. Connect the patch cord to the first LAN connector;
2. Open your personal account through the Firefox browser.

• Launch the browser and write the address of the router 192.168.0.1;
• A window with recovery mode will open;
• Click "Browse" to download the software;
• Click "Send".

The power indicator will turn off. This means that the program is being installed. The pointers lit up in standard mode, which means that the firmware is over.

Check "Network Connection" on the computer. Set the parameters for automatically obtaining an IP address and DNS server.

In order to get into the web interface of the router, you need to open your Internet browser and type 192. 168.0.1 in the address bar, user name - admin , Password - leave this field blank(provided that the router has factory settings and its IP has not changed).

Change factory password

Default: Login admin, password empty.

Tools (TOOLS), menu Administration (ADMIN).

In field New Password Enter a new password.

In field Verify Password repeat new password.

Then press the button Save settings.

After that, the router will prompt you to re-enter its settings.

Internet connection setup

In the router interface, select the tab at the top SETUP, in the list that opens, select INTERNET. We press the button Manual Internet Connection Setup

Setting up an L2TP connection (Beeline)

1. In field My Internet Connection is: select Russia L2TP (Dual access)
2. Activate below Dynamic IP
3. In field Server IP/Name enter L2TP server address
4. Username: Your login from the contract
5. Password: Your contract password
6. Verify Password: repeat password
7. Activate the item Always opposite the parameter Reconnect mode.
8. MTU: change the value to 1450 or less
9. Press the button Clone MAC Address
10. Save settings with the button Save settings

Setting up a PPPoE connection (Rostelecom)

1. In field My Internet Connection is: select Russian PPPoE (Dual Access)
2. Username: Your login from the contract
3. Password: Your contract password
4. Verify Password: repeat password
5. We press the button Clone MAC Address
6. MTU: 1472
7. ReconnectMode- connection establishment mode always-on for permanent connection
8. Save settings with the button Save settings and wait for the router to reboot.

Setting up PPtP (VPN) when automatically obtaining a local IP address (DHCP)

1. In field My Internet Connection is: select Russia PPTP Dual Access
2. Select a connection with dynamic ISP address assignment Dynamic IP
3. Press the button Clone MAC Address
4. Server IP/Name- IP/Server name of provider (ppp.lan or 10.10.3.36)
5. PPTP Account- username for authorization in the provider's network
6. PPTP Password- password for authorization in the provider's network
7. PPTP Verify Password- repeat the password for authorization in the provider's network
8. MTU value - 1372
9. ReconnectMode Always for permanent connection
10. Save settings

Setting up PPtP (VPN) with a static local IP address

1. In field My Internet Connection is: select Russia PPTP Dual Access
2. Putting a dot opposite static IP
3. IP address: We drive in your IP address according to the contract
4. subnet mask: We drive in a mask according to the contract
5. gateway: We drive in the gateway under the contract
6. DNS: We drive in the DNS of your provider (Rostelecom Omsk - 195.162.32.5)
7. Server IP/Name: ppp.lan
8. username: Your login from the contract
9. Password: Your contract password
10. Verify Password: Your contract password
11. Auto reconnect: always-on
12. MTU: 1372
13. ReconnectMode- connection establishment mode. Select Always for permanent connection
14. Save settings with a keystroke Save settings.

NAT when automatically obtaining an IP address (DHCP)

1. My Internet Connection is: select static IP
2. Press the button Clone MAC Addresses.
3. Save settings with a keystroke Save settings.

Setting up Wi-Fi on the router

In the interface of the router, you need to go to the tab Installation (SETUP), menu Setting up the wireless network (Wireless Setup). Button Setting up a wireless network manually (Manual Wireless Connection Setup).

1. In chapter WI-FI PROTECTED SETUP from point enable It is better to uncheck the box, since not all wireless adapters support Wi-Fi Protected Setup technology;
2. Specify ID SSID your wireless home network (tochka) in the field Wireless Network Name(default dlink)
3. Select a wireless channel, any channel from the dropdown list Wireless Channel
4. Select Wireless Security Mode
5. In drop down list Security Mode choose Enable WPA/WPA2 Wireless Security (enhanced) is the most secure way to protect your wireless network
6. Cipher Type-TKIP
7. PSK/EAP-PSK
8. In field network key You must enter any set of numbers, from 8 to 63 in length. They also need to be remembered so that you can specify them when connecting to the network
9. Click on the button Save settings to apply and save settings

Saving/restoring router settings

• To save the current settings of the router, press the button Save(parameter Save Settings To Local Hard Drive). The settings file will be saved to the specified location on the hard drive.
• To restore settings from a file, you must click the button Review, specify the path to the file with settings, then click the button Upload Settings.

Attention! Pressing a button Restore Device will restore the factory settings!