We are building a house 6 by 12. Schemes of one-story houses: which one to choose

The project of a 6 by 12 house made of timber has attractive facade shapes. The elegance of the building is given by the classic even configuration of the walls, an open terrace and a spacious balcony on the front side. The dimensions of the project of the house - 6 by 12 guarantee a comfortable stay for residents. The first floor of the structure contains a spacious entrance hall, a living room, a kitchen and a compact furnace with a sanitary unit. The attic of the house has an exclusive space for the relaxation of homeowners. Two chic bright bedrooms allow you to do this without difficulty. The spacious loggia provides a comfortable pastime on warm, intoxicating evenings.

The cost of construction for shrinkage from:

• timber natural humidity 150 x 150 mm - 914,000 rubles;
• profiled timber 140 x 140 mm - 970,000 rubles;
• timber of natural humidity 150 x 200 mm - 1,238,000 rubles;
• profiled timber 140 x 190 mm - 1,290,000 rubles;
• rounded log (diameter 24 cm) - 1,505,000 rubles.

Power kit price includes:

• house kit made of timber of natural moisture content of coniferous species (pine, spruce), height of the first floor 3.0 meters (cleanliness 2.55 m), raising the walls attic floor 1.5 meters, chopped pediments 3.0 meters high, washed down the corners "in dovetail"/"into the bowl" is produced on site. The erection of the wall kit is carried out on a lining board treated with an antiseptic, arranged along the perimeter of the foundation;
• internal partitions from a bar 100 x 150 mm (90 x 140 mm - when building from a profiled bar), floor and ceiling beams from a bar 100 x 150 mm in increments of 0.58 meters (according to the size of the insulation);
• the assembly is carried out on a flax jute cloth; wooden dowels with a diameter of 25 mm are used to fasten the beams together;
• manufacturing truss system, roof lathing, temporary roofing with ruberoid. Lumber and accessories: edged board 50 × 150 mm for the installation of rafters, edged board 25 × 150 (100) mm for the manufacture of roof lathing. Rafter pitch 0.6 meters;
• loading and unloading lumber. Delivery to the construction site within a radius of 50 km from the Moscow Ring Road;
• expendable materials(jute, staples, nails, roofing felt).

* Additional services:

• subfloor device - 14,000 rubles;
• treatment of the mortgage row and floor beams with an antiseptic - 6,000 rubles.

Price strip foundation- 312,000 rubles.

Qualitative characteristics of the foundation:

• tape monolithic reinforced under all external and main walls, porch;
• monolithic basement height + 500 mm from the existing ground level, width 300 mm, laying depth - 500 mm;
• sand compacted cushion, 300 mm thick from medium-grained sand;
• reinforcement AIII Ø 10 mm with an overlap of bars of at least 300 mm and a bend at the corners / intersections of the main walls;
• factory-made concrete grade M - 300 (B 22.5);
• ventilation of closed underground volumes (air vents) - pvc pipe 110 mm.

* The cost of manufacturing the foundation may vary depending on the terrain for construction (differences, slopes on the site).

The cost of a pile-screw foundation is 84,000 rubles.

• House made of timber 150x150 mm., 1st floor.
• Antiseptic treatment.
• Roof covering with ruberoid.

• House made of timber 150x200 mm., 1st floor.
• The ceiling height of the 1st floor is 2.7 m.
• Assembling the walls of the log house on wooden dowels (dowels)
• Dovetail cutting of corner joints (warm corner).
• All partitions - timber 100x150 mm.
• Floor and ceiling beams - timber 100x150 mm.
• Draft floors - board 25x100 mm.
• Roof gables - board 25x150 mm.
• Rafter system (rafters, crossbars, racks) - timber 50x150 mm.
• Roof lathing - board 25x150 mm.
• Antiseptic treatment.
• Roof covering with ruberoid.
• All consumables (wood dowels (dowels), flax fiber (jute), nails, foundation waterproofing, roofing material).
• Delivery across the Moscow region and other regions of the central part of the Russian Federation.
• Unloading and assembly at the customer's site.

• House made of timber 145x145 mm., 1st floor.
• The ceiling height of the 1st floor is 2.7 m.
• Assembling the walls of the log house on wooden dowels (dowels)
• Dovetail cutting of corner joints (warm corner).
• All partitions - timber 100x150 mm.
• Floor and ceiling beams - timber 100x150 mm.
• Draft floors - board 25x100 mm.
• Roof gables - board 25x150 mm.
• Rafter system (rafters, crossbars, racks) - timber 50x150 mm.
• Roof lathing - board 25x150 mm.
• Antiseptic treatment.
• Roof covering with ruberoid.
• All consumables (wood dowels (dowels), flax fiber (jute), nails, foundation waterproofing, roofing material).
• Delivery across the Moscow region and other regions of the central part of the Russian Federation.
• Unloading and assembly at the customer's site.

• House made of timber 145x195 mm., 1st floor.
• The ceiling height of the 1st floor is 2.7 m.
• Assembling the walls of the log house on wooden dowels (dowels)
• Dovetail cutting of corner joints (warm corner).
• All partitions - timber 100x150 mm.
• Floor and ceiling beams - timber 100x150 mm.
• Draft floors - board 25x100 mm.
• Roof gables - board 25x150 mm.
• Rafter system (rafters, crossbars, racks) - timber 50x150 mm.
• Roof lathing - board 25x150 mm.
• Antiseptic treatment.
• Roof covering with ruberoid.
• All consumables (wood dowels (dowels), flax fiber (jute), nails, foundation waterproofing, roofing material).
• Delivery across the Moscow region and other regions of the central part of the Russian Federation.
• Unloading and assembly at the customer's site.

What are the advantages of log houses?

Do you want to erect on your suburban area warm, comfortable, safe, environmentally friendly log house on a turn-key basis? Such houses are now sold in the basic configuration. Briefly describe what is included in the project two-story house 6 by 12 from profiled timber 145x145. It is assumed that it will have an attic, a veranda, an entrance hall, a porch, several rooms, a bathroom and a kitchen. By the way, the facade of such a dwelling can be finished with any material.

• The height of the first floor is 2.7 meters, the second - 2.5-2.7 meters. The walls are reinforced with each other with piping. The corners are cut using the dovetail method.
• Beams of various sizes and edged boards are used as a material for finishing the interior space. Timber - these are partitions, beams, gables, elements of the truss system. Flooring and roof grating - edged board. The material for covering the roof, protecting the room from moisture - roofing material.
• The foundation of the house is protected from the effects of ground and melt water.
• Delivery, unloading, assembly of the structure on site.

A disassembled log house can be ordered and delivered to any region of Central Russia. When developing a project for a house from a 6x12 timber, do not forget that the main thing is its competent layout.

Choosing a house project along the length of the walls is a standard approach. It gives confidence that the cottage will fit on the site. Accommodates the whole family. Will be convenient for permanent residence. Perform the main task, becoming a cozy family nest.

In the construction of houses, the length of the walls matters. More area - more opportunities to make a layout for yourself. Add bedrooms, highlight areas for relaxation, make an office or workshop. The number and functionality of rooms in the cottage depends only on the desires and imagination.

We have prepared a detailed analysis of popular standard wall size projects. Find out how the standard layout of a 6 by 6 cottage differs from 6 by 8. How to make the interior more practical. And how to effectively use the available space.

Also look. There is all the information you need for choosing: floor plans, descriptions of materials and data about the construction company. Choose, call, discuss and order.

Choose the size for yourself - what to look for

The main thing in the design of the house is the convenience of the owners. It should fit the hobbies and the rhythm of life. We are already talking about it. We recommend reading if you are seriously considering moving to your cottage.

4 points to evaluate the convenience of the project for those in a hurry:

• For one tenant - 40 m2 of area. Anything less violates building codes. And uncomfortable. Although many budget projects offer less than 40 m2 per person and it is better to live there than in an apartment.
• Consider hobbies. What is your hobby? How much space does the hobby require? You play the guitar, make furniture by hand, so you make noise and disturb others? Or quietly playing poker with friends while enjoying a cigar? Take care of the comfort of yourself and your loved ones.
• Consider home use. Who and how often will live in it? On a permanent basis or only seasonal arrivals? How often do you invite guests? The number and area of ​​​​guest and technical premises depends on this.
• Identical rooms for children. Equal area, functionality, possibilities for redevelopment. Let the children feel that their rooms are similar. This will eliminate conflicts based on envy.

We also recommend that you imagine your future home. Walk through the rooms in your mind. Place relatives and friends. Do you think everyone will be comfortable? Imagine what to change for greater convenience. Put up partitions, make new rooms, or generally increase the area of ​​\u200b\u200bthe house? Such visualization in the imagination will better reveal the features of the project.

Remember, the designers and architects of the company are ready to help. Contact them with questions. Tell me what you want to get. Even for typical projects, they will offer interior layout options. So that you move into a comfortable home and recommend the company to friends.

Typical house designs - standard layouts and helpful tips

We have chosen the most convenient and functional standard projects for popular house sizes:

• 6 by 6;
• 6 to 8;
• 6 to 9;
• 7 by 7;
• 8 by 8;
• 8 by 10;
• 12 by 12.

There are many projects. Construction and architectural companies draw their solutions to attract customers. But inside they are almost the same. Typical project, typical family - parents and 1-2 children. The main premises and floor layout are repeated. Active area on the first floor and a couple of bedrooms on the second.

Therefore, we have chosen practical, functional and comfortable designs. Where everything is thought out, there is potential for redevelopment and adaptation to the lifestyle of the owners.

For convenience, the projects were divided into two large groups:

• Up to 100 m2 - the choice of small families. Suitable for small areas. Ideal for a family of 3-4 people. Almost always little potential for redevelopment.
• Up to 150 m2 - for lovers of comfort. Big houses. Lots of extra space. Often built-in garages, saunas and baths. Several bathrooms. Great potential for redevelopment to suit your hobbies.

Remember, projects can change. Tell the designer about your hobbies. He will offer options for remodeling rooms to suit the interests of the residents.

Projects of houses with an attic up to 100 m2 - for small families or people with hobbies

Let's start with projects of houses with an attic up to 100 m2. They are compact, inexpensive. Suitable for a family of 3-4 people.

The small area imposes restrictions. The layout includes mandatory zones only: bedrooms, kitchen, living room, bathroom. Often there are no technical facilities.

The projects have little potential for adaptation. A maximum of a few square meters can be cut off from the living room or kitchen for a technical room. If you plan to live without children, you can give one bedroom as an entertainment or work area.

Standard layout and tips for zoning floors in a 6 by 6 house with an attic

Projects of houses 6 by 6 with an attic

Projects of houses 6 by 6 are mainly presented country houses. Sometimes even without a toilet inside. But we found small cottages optimized for permanent living. big family.

Such houses are the choice for starting a country life. For about 800 thousand rubles. get a cozy cottage. Ready to move in but no frills. The exact cost depends on additional services, materials and features of the site.

General features of 6 by 6 house projects

Approximate usable area 65-70 m2. Part of the space will be taken away by the area under the slopes on the attic floor.

Almost no corridors. Usually they make a small hall on the first and second floor. The living room is turned into a passage area.

Simple laying of communications. All active areas on the ground floor. Therefore, water and sewerage are diluted only through it. Heating and electricity are brought into the attic.

An example of a good compact house layout:

A minimum of corridors, all rooms are located nearby. There are few opportunities for redevelopment. But the designer can suggest options for reworking the 6 by 6 house project for you.

On the first floor:

• Hall on 5.7 m2. Separated from the living room, from the kitchen. Good decision to isolate the interior from dirt and dust from the street.
• Room of 5 m2. Connected only to the hall. Can be used as a boiler room.
• Room for 14.2 m2. You can make a kitchen.
• Room of 7.2 m2. You can make a bathroom. Enough space for a bathroom, toilet, sink and washing machine. Everything you need, nothing more

Passive zone on the second floor:

• Attic space of 24 m2. Free space is not divided into rooms. You can leave it as it is and make a large bedroom. Or split into two rooms.

Projects of houses 6 by 8 with an attic are suitable for families with children. Or for parents with older children. They have plenty of space for relaxation and daily activities. Choice for permanent residence.

Depending on the composition of the family, you can change the purpose of some of the rooms. Turn a nursery into a library, an extra bedroom into an office or cigar room.

General features of 6 by 8 house projects:

• Approximate usable area 80 m2. Even with sloped slopes, there is enough space for everything you need.
• More rooms. An additional 2 meters of walls expand the planning possibilities. You can add a bedroom on the first floor or make 3 rooms on the second floor.
• Increased space under the hall. To isolate the rooms.
• No technical room on the ground floor. The disease of typical projects of houses 6 by 8. We recommend to provide small room under the boiler room.

Projects of houses 6 by 8 with an attic

More space means more rooms. Here is a 6 by 8 house project that is functional and practical:

On the ground floor active zones:

• Entrance hall of 6.3 m2. Enough space to take off your shoes and leave outerwear. A good solution that separates street dirt from a clean house. Staircase to the attic is located right there.
• Room of 9.7 m2. You can place the kitchen here. Made next to the bathroom. For convenience, you can reduce, move to the place of the bedroom and combine with the living room.
• Room of 22.9 m2. Spacious living area to sit with family and friends.
• Bathroom 4.5 m2. One bathroom, where there is everything - bath, toilet, sink. Can fit a washing machine.

Attic - passive zone:

• Bedrooms - two of 12.4 m2 and one of 12.8 m2. Given the bedroom on the first floor, you can convert one room into something else. Transform into an entertainment center with a projector and telescope under the skylight.
• Hall on 6.8 m2. You can put a skylight and make an area with bean bags in the corner. There will be a place to relax and admire starry sky. Or take up space with furniture.

Standard layout and tips for zoning floors in a 6 by 9 house with an attic

Projects of houses 6 by 9 with an attic

Projects of houses 6 by 9 are similar to the previous ones. An additional meter of wall gives approximately 10 m2 of space. A little. This place can be used to increase all the premises, create a dressing room or boiler room.

Most of the standard projects involve the residence of a large family. Several bedrooms, spacious living room and kitchen. Enough space for everyone.

General features of 6 by 9 house projects:

• Usually isolated rooms. Sometimes they make a walk-through living room with a staircase to the attic and an entrance to the kitchen.
• Large rooms . In typical projects, the size of the rooms is increased. Large bedrooms, kitchens and living rooms. For those who love space.
• Dressing rooms. Sometimes designers cut off part of the bedroom for a dressing room. There will be a built-in wardrobe for storage.

In the planning of 6 by 9 house projects, designers continue to divide floors into active and passive ones. This project shows the standard concept:

The project of a 6 by 9 house can be adapted to any family. AT standard version there is everything for 3-5 people. Zones for sleep, relaxation and joint entertainment.

On the ground floor are usually located:

• Hall on 8.2 m2. Passage area to the living room, kitchen and bathroom.
• Living room on 20.8 m2. Spacious room to sit with family and friends.
• Kitchen on 8.5 m2. A separate area with enough space for all kitchen furniture and appliances. Can be combined with the living room and get space for an extra bedroom.
• Room of 7.5 m2. Can be combined with the kitchen and make a dining room.
• Bathroom 3 m2. The only bathroom in the house. In a large family, there may be problems with queues for the bathroom and toilet.

Take out to the attic:

• Bedrooms. The room is 12.5 m2 and the second is 15.9 m2. One of the bedrooms can be converted into a hobby area.
• Hall on 7.9 m2. Passage zone. You can put a skylight and make a place under it to relax with a table and soft chairs. An additional bathroom can be placed.

Standard layout and tips for zoning floors in a 7 by 7 house with an attic

Projects of houses 7 by 7 with an attic

Projects of houses 7 by 7 are made for small families. Several bedrooms, kitchen, living room, bathroom. There is definitely enough space for this.

The living space is approximately the same as in 6 by 8 projects. There are no special differences. The maximum in the configuration of the rooms, because the house is square.

General features of 7 by 7 house projects:

• Isolated rooms. Of the passage rooms, only the living room remains.
• Often a single space on the ground floor. The kitchen and living room are combined to make room for other rooms.
• More common technical rooms. Or additional bathrooms, depending on the priorities of the designer. In any case, such rooms are a plus for the convenience of the house.

First, let's share an unusual 3-story project. Choice for sloping areas. You can partially level it, so that the lower floor is half a basement. There you can make technical areas, a pantry or a garage.

In typical projects of 7 by 7 houses, they adhere to the standard division into active and passive zones. We picked up a project where the designer went the other way. It turned out a comfortable and functional attic.

Several recreation areas, built-in storage space, two bathrooms. Great potential for redevelopment of rooms.

On the ground floor is located:

• Entrance hall of 3.4 m2. Separates the street from residential premises. Leads to the house, bathroom and technical rooms on the ground floor.
• Hall of 4.5 m2. There is on the plan, but in reality it is not. Just a free transit zone. Leads to the living room and to the attic.
• Kitchen of 6.8 m2 and living room of 22.6 m2. The combined space makes the house more spacious. The designer singled out a separate entertainment, dining and kitchen area without partitions.
• Bathroom 4.4 m2. Small bathroom with access from the hallway.

On the second floor did:

• Hall on 3.1 m2. Small, so there is not enough space even for furniture. Leads to the bedroom, nursery and bathroom.
• Bedroom 9 m2. Combined with a wardrobe of 5 m2. You can save space on the cabinets and put only the bed. Leads to a spacious balcony.
• Children's or teenager's bedroom of 10 m2. The project has space for a small dressing room. Leads to the second balcony, through which you can get to the bathroom.
• Bathroom 6.7 m2. With bath, toilet and sink. Solves problems with queues for the bathroom, because there is another bathroom on the ground floor.

Projects of houses up to 150 m2 - there is enough space for everyone

In projects of houses with an attic up to 150 m2, there are more expensive solutions. They make built-in saunas, a garage, extended technical rooms, several bathrooms with bathtubs on the second floor. More often add functional basement rooms. You can find layouts with work areas, offices or workshops on the ground floor.

Such projects are suitable for a big family from 4-6 people or several tenants with different hobbies. All rooms are spacious. Therefore, an extra bedroom can be turned into an entertaining or work room. No complex remodeling.

Large houses are more often chosen for building a family nest. When they plan that children and grandchildren will live here at the same time.

Projects of houses 8 by 8 with an attic

Projects of houses 8 by 8 are suitable for a large family. Comfortably fits several generations or adult children with their parents. Proper organization The interior space creates zones for joint entertainment and recreation.

Such projects are universal. Bedrooms can be made into offices or workshops. Divide the living room into 2 parts and create a separate recreation area. It all depends on the hobbies of the residents.

General features of 8 by 8 house projects

• Technical buildings. In the projects of houses 8 by 8, technical rooms are more often laid. Places for a boiler room, communications and a dressing room will be without redevelopment.
• Several bathrooms. Usually two. On the ground floor there is a toilet with a sink. On the second - a combined bathroom. Solving the problem of queues to the toilet in a large family.
• Isolated rooms. Designers isolate all rooms. Passage rooms disappear. Occasionally through the living room they make an exit to the courtyard.

Standard layout and tips for zoning floors in an 8 by 8 house with an attic

Typical projects are different. In some, many small rooms are made on the ground floor to allocate space for a built-in sauna. In practice, this is inconvenient. Square meters spent on the steam room, it is better to put it into the kitchen or an extended bathroom.

We chose functional standard project houses 8 by 8. It takes into account everything:

On the first floor are located:

• Technical buildings. Wardrobe 4.8 m2, boiler room 7.1 m2 with a back door to the street. The problem with laying communications, installing a boiler and storing things has been solved.
• Tambour 1.9 m2. A small area where you can only put shoes.
• Hall on 5.7 m2. buffer zone. There is only enough space for a hanger in the corner. Leads to other rooms and to the attic.
• Bathroom 2.3 m2. Only sink and toilet. The main bathroom was taken out of the attic.
• Combined kitchen and living room of 30.2 m2. The dining area is the size of a 1-room apartment. It can be divided into two parts, highlighting the recreation area. Leads to a patio with a terrace.

On the second floor there are:

• Hall on 5.2 m2. buffer zone. There is enough space for small bedside tables in the corner next to the bathroom and by the railing.
• Bathroom 7.1 m2. Bathtub or large shower, toilet and sink, washing machine. Enough space for everything you need.
• Bedrooms of 11.1 m2, 13.7 m2 and 15.6 m2. A small family can remake one. Turn into a workshop, library, entertainment room or office.

Standard layout and tips for zoning floors in an 8 by 10 house with an attic