Is it possible to make a kitchen sofa with your own hands? Do-it-yourself kitchen corner sofa Do-it-yourself soft sofa for the kitchen

Planning to update your kitchen furniture? Then read the step-by-step instructions on how to make a kitchen corner with your own hands. Now it is not necessary to buy a ready-made headset, because in a short time you can make it yourself. Corner sofa for the kitchen – perfect solution for small spaces. Make inexpensive repairs in the apartment or country house without the involvement of experts.

How to make a corner sofa in the kitchen with your own hands

The standard set of furniture for arranging the dining area includes a table, corner sofa and stools.

Drawing and dimensions of a standard corner sofa in the kitchen

According to step by step instructions, to make a corner sofa for the kitchen, you need:

• Board made of birch, beech or pine 2 by 4 cm - 100 cm.
• A beam with a section of 4 by 4 cm, about 135 cm.
• Beam 2.5 by 2.4 cm, about 365 cm.
• A beam with a thickness of 1.5 by 1.5 cm - 300 cm. For sheathing the back wall, a fiberboard sheet.
• Plywood 0.8 - 1 cm thick at the bottom and for the sides.
• You also need 5 cm thick foam or synthetic winterizer.
• Upholstery fabric (microfiber, tapestry, leather, nubuck and others).

To make a corner sofa for the kitchen with your own hands, prepare:

• jigsaw
• carpenter's corner
• plane
• furniture stapler
• screwdriver
• Sander
• drill
• bit
• hacksaw
• pliers
• roulette
• a hammer

You will also need: confirmations, screws 0.4 by 2 cm, 0.4 by 6 cm and 0.4 by 8 cm, bolts and 0.8 cm washers, dowels, legs, hinges. If it is planned to manufacture folding sofa do it yourself, then according to the instructions, you need a special mechanism. In the drawing of the sofa in the kitchen, the calculated dimensions and dimensions should be written. In this case, your kitchen corner will fit perfectly into the dimensions of the room.

Do-it-yourself drawing of a sofa in the kitchen

The blanks are ground and leveled, and only then they can be marked and sawn. The average length of the corner sofa is 120 by 90 cm, the corner insert is 45 by 45 cm, and the back height is 85.5 cm.

First, according to the drawings, the main parts of the sofa are made from the kitchen corner - these are the sidewalls. They are made from thick plywood. The marking is done with a pencil, and then the detail of the kitchen corner sofa is cut out along the lines with an electric jigsaw.

The next step is to make two frames for both sides of the sofa from 4 by 4 centimeters bars. Both frames should be in the form of parallelepipeds, which are then fixed on the sidewalls. The joints at the corners should look like a mustache and a spike, which are subsequently glued. The T and L form joints must be at a 90 degree angle.

Do-it-yourself drawing and assembly diagram of a kitchen sofa

At the corners, the joints can be with through holes or hidden, go to half the beam, and also be one, two, three spiked. They are fixed with dowels or corners with self-tapping screws.

The frame of the corner sofa for the kitchen is connected to the back and fixed on the sides. When the base is ready, you can assemble the folding seat covers. Seats can be solid or sectional.

Rectangular seat frames are made from a bar 2.5 by 2.5 centimeters thick. Then they are sewn up with centimeter plywood. The seats are cleaned and covered with a layer of stain and varnish. Then the foam rubber is glued, and the fabric is stuffed.

A piano loop is attached to the long part of the seats of the corner sofa. Hinged covers are fixed at the end of the work. The assembly of the corner module is carried out in a similar way. A frame is made from a bar 4 by 4 centimeters. The profile must have triangular shape and have sides at 45 and 90 degree angles. The module is covered with plywood.

The assembled two parts of the sofas and the corner module are sanded. Open wooden elements are opened with a stain and, accordingly, three layers of varnish on top. All details are put on the sofa legs and fastened together. The connection is made with screws to the frame support. There must be at least 8 legs.

Structural details are exposed while adjusting the height of the legs. Marks are made in the places of future fastening. Holes are drilled for bolts with a diameter of 0.8 centimeters. Bolts and washers to them should be with wide margins. The washer should be twice as many bolts, so that one goes under the bolt and the other under the nut.

Upholstery fabric depends on the location of the sofa from the stove and sink. The surface should be easy to clean and not exposed to chemicals.

For a small sofa, 5 cm foam rubber is suitable. For a semi-soft corner bigger size, the stuffing is taken from the synthetic winterizer. Foam rubber or synthetic winterizer is glued to the back with glue. The fabric is cut out according to patterns and nailed with a stapler from the back of the back, as well as at the junction of the back with the seat. The material is stretched and securely fixed at the corners. Then it is fixed around the entire perimeter.

Armrests are made from a bar 4 by 4 cm thick. Do not forget to make grooves with a depth of 2 - 3 cm. The width of this selection depends on the thickness of the wall side. The workpiece is trimmed with filler and upholstered with fabric. The armrests are covered with glue, inserted into the sidewalls and fixed with screws. Such a beautiful and uncomplicated sofa will last a long time, and its execution will require much less cost than when buying a finished one.

After that, you can start making a table or chairs. A step by step video guide will help you.

Video with drawings: How to make a kitchen corner with your own hands

Your Kitchen Area ready, now you can equip a comfortable zone in the kitchen with your own hands. Furniture for the kitchen is quite simple to make, while it will last a long time without losing its original attractiveness.

The place where the family meets for breakfast, lunch and dinner has always been considered almost the center room in the house. That is why many people try to make a kitchen sofa with their own hands, since it is not always possible to choose the ideal option in the store. Independent work not only gives a spectacular result and is considered practically free, but also helps to relax and be alone with your thoughts.

It is worth noting that today, the sofa has become a very popular kitchen furniture. You can rest on it, even if its dimensions are not too large. In addition, the folding version can serve as a great option. bed when such a need arises.

Benches and benches are a thing of the past, even for small kitchens you can make an excellent sofa that will become a central piece of furniture.

Making a sofa for the kitchen with your own hands is quite simple to make if you prepare drawings and diagrams for the selected model in advance. But first you need to decide which model you want to get as a result. It is more difficult to make a corner sofa for the kitchen with your own hands, and if you do not have experience, you should choose a simpler option for work.

1 2 3

Assembly schemes are available for all types, so do not worry about the preparation. But, as practice shows, corner sofas are more popular than other options, as they qualitatively capture small areas near the walls of the kitchen and correctly divide the space. In addition to the corner sofa, the following types of upholstered furniture can be made in the kitchen:

• sofa book and eurobook;
• retractable sofa;
• folding sofa.

Folding sofa

Externally, the sofa in the kitchen can be decorated absolutely as you wish. In this case, there are no restrictions, because in any case a person makes an individual version for his own use. If you decide to immediately make a sofa for the kitchen with a berth, then you should prepare the mechanisms in advance that will help when unfolding the furniture.

What do you need to work?

Remember that what you are going to do is not just a bench, but a beautiful and original cushioned furniture. Sofas in the kitchen, although they are prepared for quite short term, but still require the involvement of many tools, such as:

• drill;
• electric jigsaw;
• screwdriver;
• plane;
• building level;
• ribbon;
• sandpaper;
• construction stapler and staples.

In addition, you should think about your safety. Wear gloves and goggles when working to avoid even minor injuries.

Progress of the main work

For example, if you decide to make a kitchen corner sofa with your own hands, you will need step-by-step instructions. You can find it on the Internet, with all sizes, both for small and large options.

Dimensions for corner sofa Dimensions chart

It would be best to start with the manufacture of the frame. By individual sizes details of the future sofa are made, in which drawings and diagrams help a lot. The frame is assembled using screws, which must be fixed as well as possible so that the sofa does not loosen during operation and does not have to be restored.

Corner sofa assembly diagram

Plywood will be enough to make the frame, and after that bars are attached to it, which take on the main load when used. Remember that this furniture must withstand a fairly large weight, so the dimensions of the bars should not be too small. Experts advise taking boards for work, the thickness of which is at least one and a half centimeters. But, if your bars are more than the specified limit, there is nothing to worry about, the main thing is not less.

After all the bars are firmly fixed, you need to do correct angle. Since plywood itself bends quite well, there should be no problems, the main thing is not to overdo it with deflection.

Making the finished model

If you were able to make a sofa for the kitchen with your own hands, then you can definitely cope with its upholstery. To do this, you may only need a construction stapler and staples, and you can also prepare a project or drawing in advance that could make your plan a reality and prevent you from missing some important details. The main thing is not to feel sorry for the foam rubber on the made sofa. This material makes furniture the most usable, and since we all spend a lot of time in the kitchen, a comfortable place to relax is a must.

Remember that the furniture is made for the kitchen and therefore the fabric for the upholstery should be chosen one that will not be difficult to clean later. Various prints and decoration elements will help make it more colorful, as well as correctly place the sofa in the kitchen. In addition, in order to keep it clean, you can use the original covers or capes.

When wondering how to make a beautiful sofa in the kitchen with your own hands, answer yourself that everything is quite simple and possible. The main thing is to believe in yourself and follow the prepared drawings and diagrams. Remember that making furniture yourself, you will significantly save the family budget. In addition, as a result, you will receive not just the same type and standard store model, but an individually executed project that no one else has.

Having received this knowledge and skills, you can not stop there, but conquer new heights in the independent manufacture of furniture. Sofas are needed always and everywhere, and original sofas are generally quite difficult to find, making it yourself is much easier.

Comfortable and stylish corner sofa in the kitchen is the best option compact and functional headset. Such stationary models, which fold out and come with right- and left-hand modes, promise the owner sincere conversations at the table, romantic dinners, relaxing dinners. Specialized stores offer a wide range of furniture and sets. In order to choose the right option for yourself, and at the same time not to get lost in the presented variety of corner sofas for the kitchen, you need to remember the main thing, namely: preferences, interior style, size of the kitchen.

Features of creating a sofa with your own hands

Figure 1 - furniture dimensions

It is much more comfortable to sit on corner furniture than on a regular chair. After all, the spine in this case is less tense, and, therefore, rests more. This wonderful design makes the kitchen not only a place for cooking and eating, but also a full-fledged corner for relaxation. Many make a kitchen sofa with their own hands. This will significantly save money, and the result will meet all expectations. Furniture made by hand brings maximum convenience and joy in operation, and you can think over the design and style yourself down to the smallest elements. The process will be greatly simplified if you first create drawings and weigh each step.

How to make a corner sofa

Figure 2 - furniture with a berth

To get started, purchase material such as plywood, leather substitute for upholstery, and dense foam rubber. Sketch out the appearance of the desired furniture, and then proceed to a more detailed drawing of the corner sofa in the kitchen. If you do not understand the layout and do not know how to draw drawings at all, then it is better to contact a professional designer who will help you do everything according to the rules. For example, you can make a drawing of a traditional version, shown in Figure 1, or an unusual transformer, shown in Figure 2.

If you are making a kitchen corner sofa of this kind, the pattern will be an arc that fits into the corner of the kitchen. Photo 3 shows that the headset fits perfectly into the size of the room.

On the next step carefully cut out the individual parts of the corner sofa for the kitchen. Using jumpers from a bar or any other strong device, connect the side parts into one. In the same way, combine the remaining parts so that the structure is ready for installation. The sofa in the kitchen is almost ready, it remains to cut the seat and back out of plywood. Then, according to the drawings, cut out a soft seat from foam rubber.

In order to evenly fill the frame, the material must be stitched independently.

Now you have a unique, handmade sofa for the kitchen that will complement the interior and give the room a special sophistication. Note that you choose the style, configuration and coloring of the furniture yourself. The corner kitchen sofa is one of the main elements that attract the attention of every guest. Such an element can become a so-called transformer. On some legs, place wheels made of durable metal to make it easier to transport furniture. In addition, the side of the structure can be combined with any element of the kitchen set, thus creating an interesting modular model. Inside the sofa you can place personal items: canned food, preparations for the winter, household appliances. In order to create a cozy and warm atmosphere, it is very important to correctly arrange the furniture in the space of the room.

There is an option to create a simple corner sofa for the kitchen. It is made from an old kitchen corner. Most often, this kind of furniture finds a place in country house or on the porch. In order to update old furniture, you will need new upholstery, foam rubber, as well as a construction stapler. Soft original sofa for the kitchen will be the main pride of the owner.

Advantages and disadvantages of corner kitchen sofas

This kind of furniture has such advantages as:

• It has a large seating area compared to an ordinary straight sofa.
• Saves space in the kitchen in length, respectively, can be located even in a small room.
• It is outwardly original and attractive, and also forms a cozy island for relaxation.
• Variety of designs and color solutions allows large selection, which, in turn, allows you to choose the most suitable colors and materials in one style or another.

The disadvantages of corner sofas include:

• Sometimes corner sofas are large, which does not allow them to fit harmoniously into a small apartment.
• Corner furniture, as a rule, is more expensive than standard furniture.
• Making a corner sofa on your own is difficult if this is your first time encountering such work.

Thus, if the apartment or house has a small kitchen, it is recommended to make a sofa with one corner, which will save space and fit organically into the kitchen interior.

The decision to make a kitchen corner with their own hands is usually taken by those who are disappointed with the assortment offered by furniture stores. Order individual project will cost a lot, and a corner sofa made with your own hands will be inexpensive. Moreover, when choosing suitable model and in the assembly process, you can use any material, take into account color scheme and the general style of the room.

First of all, you need to decide on the configuration. You need to understand how the kitchen corner will stand, in which direction it will be turned. It depends on the area of ​​\u200b\u200bthe room, the location of other furniture.

Before deciding which kitchen corner to make, it is worth looking at photos of finished projects.

Solid wood kitchen corner

Kitchen corner upholstered in leatherette

Shelf kitchen sofa

Kitchen corner sofa with cushions

Large corner sofa

Wooden kitchen sofa

Folding corner for the kitchen

Kitchen corner made of planks

wooden corner

Corner for a large kitchen

Take measurements of the kitchen, measure the angle of the room. Focusing on them, determine the depth and length of each sofa, the height of the frame, the location of the sections. You can use ready-made drawings by correcting them.

Chipboard kitchen corner: step by step instructions

Consider how to make a corner for the kitchen with your own hands, consisting of 3 elements: a short and a long sofa and a part connecting them.

Kitchen corner: top view

Material selection

To make the base of the kitchen corner with your own hands, you can use plywood or chipboard.

As upholstery on the kitchen corner is used:

1. Synthetic fabric. Material is different affordable price, color fastness, easy to clean.
2. Microfiber. It has increased resistance to moisture, practicality - it is slightly susceptible to pollution. The kitchen corner, upholstered with it, will not need restoration for a long time.
3. Leatherette. Easy to clean, does not absorb water, can be wiped with a damp cloth.

As a filler, you can use foam rubber (budget solution) or polyurethane foam - it costs more, but retains its shape better.

For more information on how best to upholster a kitchen corner, you can learn from the video

Materials and tools

To make a soft corner, you will need:

• jigsaw (if sawing sheet material planned independently)
• furniture corner metal;
• edge for ends;
• wood glue;
• pencil;
• nichrome thread;
• drill and a set of drills;
• scissors;
• fasteners (dowels, confirmations);
• piano loops;
• furniture pads;
• construction stapler;
• roulette;
• a hammer.

Making a corner in the kitchen with your own hands, they start by cutting chipboard.

Making a long sofa

The kitchen corner of this model consists of 3 elements: two sections and a connecting corner piece.

Diagram of a long sofa

Sofa

The back, seat, bottom and wall of the niche, the backrest stop bar are made of polished chipboard, the rest of the elements are made of laminated. Sidewalls will need 2 pieces, other parts are cut out in 1 copy. The dimensions of each element of the corner structure are visible in the drawings.

The front of the niche

sidewall

niche wall

Top bar

seat bar

Back support bar

The procedure for the manufacture and assembly of the sofa:

1. Mark out details for milling. In places where fasteners will be located, put dots with a pencil, drill holes.
2. The ends of the sidewalls are closed by gluing an edge on them.
3. At the ends that will be in contact with the floor, the thrust bearings are fixed, fixing them with self-tapping screws.
4. Move on to niche assembly. They take the front panel, the wall and the bottom of the niche, connect the parts with the help of confirmations.
5. The sides of the niche are closed by attaching the previously prepared sidewalls to them.
6. The seat bar is screwed to the wall of the niche. It is fixed on dowels.
7. A seat is installed, it will be lifting, hinges are used to attach to the bar.
8. Secure the backrest blank using dowels.
9. Mount the upper bar on the back, under it - the thrust bar. Fix the elements with an additional two metal corners.

Scheme for marking holes for fasteners on the sidewalls

Back. Back view

After the assembly is completed, go to the upholstery.

Assembled sofa (back view)

2 pieces are cut out of foam rubber. Thick foam rubber can be cut evenly with a nichrome thread, material less than 5 cm thick is cut with a knife.

For the back, a piece is cut, the length of which is equal to the length chipboard sheet, and the width is made 4 cm more. Fix it so that 2 ends are covered with foam rubber. Glue is used for fixation.

For the seat, a blank is cut out equal to the length of the seat, and 2 cm wider. Fasten so that the front end is closed.

foam fixing

Then the upholstery fabric is cut. You will also need 2 parts - for the back and seat. They need to be cut in such a way as to completely wrap the upper sides of the chipboard along with the foam rubber, while leaving a few centimeters of fabric on each edge, which is attached to the chipboard with a stapler. Staples are driven in every 2 cm.

First, 1 long side is fixed, then, after stretching the fabric a little, the opposite is nailed, then they move to the side ones, straightening the material.

Short sofa

Sofa

They cut the parts from which the sofa will be assembled, focusing on the drawings.

Top bar

Backrest support bar

seat bar

niche wall

The front of the niche

The sidewalls, the front side of the niche, the seat rail and the upper backrest rail are made of laminated chipboard, the rest are sanded. Sidewalls will need 2 pieces, other parts - 1 each.

The process of assembling a short sofa is similar to making a long one.

Connecting part

This element will connect the short and long sections into a corner sofa.

connecting corner

Corner plank

Center back

From chipboard 16 mm thick you need to cut out:

• 2 slats for the back;
• a workpiece that will be installed at the level of the seat;
• trapezoidal part of the back, which will be located in the center;
• lateral parts of the back.

Assembly order:

1. First, connect the side parts of the back to the central one. Dowels and confirmations are used.
2. Attach 2 thrust strips to the back, fixing them with dowels and metal corners.
3. Connect the structure with the side parts of the sofas.
4. The seat is upholstered using foam rubber and fabric.
5. Fix it between the sidewalls of the sofas, using confirmations and metal corners.

The soft corner is ready.

Making a kitchen corner with storage boxes

A less complex kitchen nook can be made from furniture board or thick plywood.

The design consists of 2 connected rectangular parts with backs. Despite the simplicity, the finished corner can look spectacular: it can be painted, covered with fabric seats, and pillows can be placed on the back.

Scheme of a corner with drawers

Materials and tools

To make a corner sofa, you will need a furniture board or plywood with a thickness of at least 18 mm. In addition to them, you need to prepare:

• upholstery fabric;
• jigsaw;
• roulette;
• pencil;
• self-tapping screws;
• foam rubber;
• nichrome thread;
• drill and a set of drills;
• plastic thrust bearings;
• metal furniture corner;
• water-based paint;
• brush, cuvette;
• primer.

Cutting parts and assembling the frame

Procedure:

1. Using the drawings, they transfer the details to the furniture board, saw them using a jigsaw. It is important to hold the blade so that a right angle is formed.
2. Assemble the base of the sofa: first, the bottom is screwed to the front, then the back wall.
3. A transverse bar is installed in the central part of the workpiece. It should form a right angle with the front and back sides. The bar will serve as an additional support for the seat so that it does not bend under the weight of the seated person.
4. After installing the sidewalls.
5. In the same way, make the second sofa.
6. Using self-tapping screws, connect both bases to each other to make a corner sofa.
7. The backs are screwed to each blank, at the junction on the back side they are fixed first with confirmations, and then a metal corner is installed. Before screwing in the screws, first mark the location of the fastener and drill holes using a drill with a diameter 0.5 mm less than the diameter of the screw.

Before you fully assemble the kitchen corner, placing the seat covers on the base, the workpiece is painted.

Unpainted frame

Frame decoration

Furniture board or plywood can be painted, stained or varnished. Before proceeding, the corner is covered with an antiseptic primer - it will protect the tree from decay, and also improve adhesion. All parts are carefully primed on both sides, and then left to dry completely. Separately, a primer is applied to the seats, which are not yet fixed to the frame.

If you decide to paint the corner, then it is better to take a water-based paint, such as acrylic. It is resistant to contact with water, retains brightness for a long time, does not wear out.

painted corner

Assembly

When the paint has dried, begin to collect the corner. The seats are connected to the frame with hinges.

Upholstery

Instead of the usual upholstery for this model of a kitchen sofa, you can use soft pillows.

For this:

1. Foam rubber 8 cm thick is cut into 2 parts, the dimensions must match the parameters of the seat covers.
2. Covers for foam rubber are sewn from fabric.
3. They put them on blanks.

The soft corner of the furniture board for the kitchen is almost ready - it remains to put pillows on the backs or cover them with a cloth.

Board corner

An easy-to-assemble corner for the kitchen can be made from ordinary wooden boards.

Corner for the kitchen from the boards

You will need:

• boards 100*40 mm;
• stapler;
• foam rubber;
• jigsaw;
• roulette;
• dowels;
• drill, nozzle-crown with a diameter of 1.5 cm;
• building glue;
• sandpaper;
• batting;
• upholstery material;
• varnish, paint brush;
• pencil.

Sawing parts and making a frame

The corner is made, guided by the parameters of the kitchen. The diagram shows all the details, so detailed drawings are not required.

Frame diagram

If you still need a diagram, you can watch a video on how to build a template yourself

Having chosen the optimal depth and length, cut the boards into segments of the desired size.

You will need:

• 3 racks;
• 2 legs;
• 3 cross elements of the same length for a long sofa;
• 5 identical crossbars for short;
• 4 identical bars for the sides of both sofas (2 for each side);
• 2 cross elements for a long sofa.

After the elements that make up the corner are cut, they are carefully polished using sandpaper. Start with coarse, then apply medium.

Mark holes for dowels. Each element of the frame must be connected to another with 2 dowels. Drill holes for them using a drill with a crown.

Lubricate the holes with carpentry glue, insert dowels, tightly fit the parts to each other using a hammer. It is important to ensure that there is a right angle between the elements, distortions should not be allowed.

Each inner corner structures are strengthened by screwing a metal corner to the boards.

Coating with varnish or stain

The wooden base is covered with 2 layers of varnish or stain. If the latter is used, after the frame has dried, it must be sanded again, since the pile on the wood rises from the wood stain, and there is a risk of planting a splinter.

Assembly

Assembly and painting of the frame

On each lower crossbar, a metal corner is fixed on the inside at the same level - it will hold the bottom of the box.

Fixing furniture corners

2 blanks for the bottom are cut out of chipboard. Lay them on the frame.

bottom of drawers

Cut out 2 front strips for the box, 2 side. They are fixed from the inside of the frame, so that the lower end is in contact with the bottom. Fix on self-tapping screws to the boards.

Cut out 2 seat covers. Their dimensions should be 2 cm larger than the width and length of the boxes, so that when closed they are securely held on the frame.

sheathing

Before you fully assemble the corner for the kitchen, the covers are sheathed. First, foam rubber is glued to the base, then wrapped with batting, fixing it with a stapler, and then sheathed with furniture fabric.

Cloth upholstery

The final step is to install the seat. Both blanks are attached to the rear crossbar of the frame on the hinges.

The corner sofa for the kitchen from ordinary boards is ready.

Renovation and restoration of the kitchen corner

If a do-it-yourself kitchen corner has begun to look unsightly, it can be restored by returning its original appearance. The method depends on which part of the furniture needs to be updated - the frame or the upholstery.

frame

The front parts of the frame, made of wood or plywood, can be painted, varnished, stained.

For this you need:

1. Dismantle elements upholstered in fabric.
2. Remove the old coating, if any. Residues of paint can be cleaned off with sandpaper.
3. Seal fittings or other parts of the frame that should not get paint with masking tape.
4. Using a cuvette and a brush, carefully cover the kitchen corner with 1-2 layers of varnish, stain or paint.

Upholstery replacement

The process of replacing faded, stained or torn upholstery is quite simple. It is not required to completely disassemble the corner for the kitchen - you need to remove the sofa seats from the hinges, and dismantle the backs.

After removing the fabric, pulling out the staples, tear off the foam rubber from the slats. Cut out details of the desired size from foam rubber and fabric (leatherette, velor, microfiber, etc.), taking into account the dimensions of the wooden elements. Then upholster again, proceeding in the same way as in the manufacture of furniture.

Replacement of foam rubber and upholstery on the sofa: before and after

Making a kitchen corner with your own hands is not too difficult. The main thing is to accurately cut out all the details, adhering to the dimensions indicated in the drawings. Even a slight deviation can lead to a distortion of the structure.

Soft kitchen sofas are the most popular pieces of furniture used for furnishing kitchen space or dining area. They are quite functional, while not taking up too much space, which is important for small spaces. In addition, the design of such a piece of furniture is quite simple, so anyone who knows how to hold a hammer, a screwdriver and a drill can make a sofa in the kitchen with their own hands. And so that during the manufacturing process you do not have any difficulties, our specialists will reveal to you in detail all the subtleties and nuances of this process.

First of all, you should decide on appearance sofa, which I would like to get as a result. You should not overly complicate the design and introduce creative elements that are complex in execution, because not everything can be done at the proper level at home. It is worth stopping at a simple but convenient option that will delight you and your guests.

A standard sofa should have a frame resting on legs; roller mechanisms can also be used. The design with folding seats gives access to niches that can be used as drawers. At the same stage, you need to decide how soft the sofa you want, what color scheme and upholstery material should be, in order to make it easy to clean in the future.

You need to be very careful when planning the size of the future sofa, since the dimensions should be commensurate with the place that it should take. It is necessary to make all measurements in advance and prepare a drawing for the manufacture of furniture.

If this is your first experiment in making furniture at home, then you should stop at the folding version, and not at the manufacture of the corner. The rectangular shape of a sofa with legs is much easier to make, and it is much more difficult to make a mistake in size calculations.

The frame can be made of timber, for this, pine rocks are better suited, which are fastened with screws. To avoid the formation of longitudinal cracks, it is worth placing fasteners at different levels. To make the structure as strong as possible, the bars should be screwed to the corners of the frames, which have a cubic shape.

Screws will act as fasteners, since they are most convenient to fix wooden structure. The bottom of the sofa, like the seat covers, is best made from plywood.

The standard set of furniture for arranging the dining area includes a table, a corner sofa and stools.

According to the step-by-step instructions, to make a corner sofa for the kitchen, you will need:

• Board made of birch, beech or pine 2 by 4 cm - 100 cm.
• A beam with a section of 4 by 4 cm, about 135 cm.
• Beam 2.5 by 2.4 cm, about 365 cm.
• A beam with a thickness of 1.5 by 1.5 cm - 300 cm. For sheathing the back wall, a fiberboard sheet.
• Plywood 0.8 - 1 cm thick for the bottom and for the sides.
• You also need 5 cm thick foam or synthetic winterizer.
• Upholstery fabric (microfiber, tapestry, leather, nubuck and others).

To make a corner sofa for the kitchen with your own hands, prepare:

• jigsaw
• carpenter's corner
• plane
• furniture stapler
• screwdriver
• Sander
• drill
• bit
• hacksaw
• pliers
• roulette
• a hammer

You will also need: confirmations, screws 0.4 by 2 cm, 0.4 by 6 cm and 0.4 by 8 cm, bolts and 0.8 cm washers, dowels, legs, hinges. If it is planned to make a folding sofa with your own hands, then according to the instructions, you need a special mechanism. In the drawing of the sofa in the kitchen, the calculated dimensions and dimensions should be written. In this case, your kitchen corner will fit perfectly into the dimensions of the room.

The blanks are ground and leveled, and only then they can be marked and sawn. The average length of the corner sofa is 120 by 90 cm, the corner insert is 45 by 45 cm, and the back height is 85.5 cm.

First, according to the drawings, the main parts of the sofa are made from the kitchen corner - these are the sidewalls. They are made from thick plywood. The marking is done with a pencil, and then the detail of the kitchen corner sofa is cut out along the lines with an electric jigsaw.

The next step is to make two frames for both sides of the sofa from 4 by 4 centimeters bars. Both frames should be in the form of parallelepipeds, which are then fixed on the sidewalls. The joints at the corners should look like a mustache and a spike, which are subsequently glued. The T and L form joints must be at a 90 degree angle.

At the corners, the joints can be with through holes or hidden, go to half the beam, and also be one, two, three spiked. They are fixed with dowels or corners with self-tapping screws.

The frame of the corner sofa for the kitchen is connected to the back and fixed on the sides. When the base is ready, you can assemble the folding seat covers. Seats can be solid or sectional.

Rectangular seat frames are made from a bar 2.5 by 2.5 centimeters thick. Then they are sewn up with centimeter plywood. The seats are cleaned and covered with a layer of stain and varnish. Then the foam rubber is glued, and the fabric is stuffed.

A piano loop is attached to the long part of the seats of the corner sofa. Hinged covers are fixed at the end of the work. The assembly of the corner module is carried out in a similar way. A frame is made from a bar 4 by 4 centimeters. The profile should have a triangular shape and have sides at angles of 45 and 90 degrees. The module is covered with plywood.

The assembled two parts of the sofas and the corner module are sanded. Open wooden elements are opened with a stain and, accordingly, three layers of varnish on top. All details are put on the sofa legs and fastened together. The connection is made with screws to the frame support. There must be at least 8 legs.

Structural details are exposed while adjusting the height of the legs. Marks are made in the places of future fastening. Holes are drilled for bolts with a diameter of 0.8 centimeters. Bolts and washers to them should be with wide margins. The washer should be twice as many bolts, so that one goes under the bolt and the other under the nut.

Upholstery fabric depends on the location of the sofa from the stove and sink. The surface should be easy to clean and not exposed to chemicals.

For a small sofa, 5 cm foam rubber is suitable. For a semi-soft corner of a larger size, padding is taken from synthetic winterizer. Foam rubber or synthetic winterizer is glued to the back with glue. The fabric is cut out according to patterns and nailed with a stapler from the back of the back, as well as at the junction of the back with the seat. The material is stretched and securely fixed at the corners. Then it is fixed around the entire perimeter.

Armrests are made from a bar 4 by 4 cm thick. Do not forget to make grooves with a depth of 2 - 3 cm. The width of this selection depends on the thickness of the wall side. The workpiece is trimmed with filler and upholstered with fabric. The armrests are covered with glue, inserted into the sidewalls and fixed with screws. Such a beautiful and uncomplicated sofa will last a long time, and its execution will require much less cost than when buying a finished one.

As one of the options for making a kitchen sofa with a folding mechanism, meralat is forward.
For production, ordinary furniture materials and tools will be required. We replace all missing elements with analogues if necessary.

We use 15 mm plywood. Optional 20 mm. If we consider a cheap inexpensive option, then we take chipboard, preferably at least 18 mm. But in the end, it can affect the life and quality of the product.

We assemble the plywood frame and wooden beam for wood screws.

We glue with foam rubber and synthetic winterizer. We insert the folding mechanism of the required width of the bed.

This is what the sofa will look like when unfolded.

The mattress is sold with the mechanism, but it will be cheaper to do it yourself. We select the density of foam rubber according to the desired softness and service life.

Fabric upholstery. In this case, velor is used. For simplicity, you can make joints in some places, and not with a solid cover, as in the photo.

Pillows for sitting are pasted over with padding polyester. The seat is made of blue and white foam rubber of different densities.

We try on how it will look in height and width. We select best option for myself. The standard seat height is 45 cm.

Cover the mattress with fabric. This is what the finished product looks like when unfolded. A mechanism with a width of 100 cm was used. The overall width of the sofa is about 125 cm.

The key to success in making furniture with your own hands

In the manufacture of furniture, the main thing is patience, calmness and knowledge. If you do not rush, at the first stages you carefully work out the scheme of the sofa and make a drawing of it with all dimensions, then there will be no problems at the stage of cutting and assembling the structure. But everything is early, you should be prepared for difficulties in the process, especially if you are doing this for the first time. They should be treated as a normal working moment, you should not panic and get upset if something did not go the way you wanted it to. We need to stop and think about how to fix this situation. You always have the opportunity to change and redo everything, because this is the advantage of making a sofa with your own hands, that you yourself can change all the flaws and shortcomings in the work at any time.